Stock: 9969
- Full-Print Rear Oval Overlays - Big Foot, Skull and Pistons, Come and Take It, Big D Energy, and Jeep Recovery Vehicle designs.
- Goes Over Your OEM Emblem - install it right over the factory oval, no emblem removal.
- Fits 2021+ Bronco AND Bronco Sport - verified on both.
- Custom and Factory-Matched Colors - printed to match named Ford colors, with more than 20 color options.
- Gloss Overlaminate - protects against UV and the elements.
- Dry or Wet Install - both install videos are below.
- Made in the USA - printed and cut by StickerFab in Fort Myers, FL.
Printed Series Rear Oval Emblem Overlays for the 2021+ Ford Bronco and Bronco Sport
Replace the factory look on the back of your Bronco with a design that is yours.
Full Printing Means More Color ChoicesPlease help us with new ideas for the oval as we make our transition to custom products that replace the factory branding. Full printing allows us to make custom colors with a lot more ease than off-the-shelf vinyl. Pick a design, pick a color, and the overlay goes right over your OEM emblem. |
 |
 |
Five Designs to Choose From
|
About the Colors
We have either gone to a dealership or surveyed customers by sending them color swatches to create these options. This is the closest that we can get to the named colors by printing. Each vehicle is sampled in a few locations in and out of the sun to obtain the best results.
Factory-matched colors include: Antimatter Blue, Area 51, Cactus Grey, Carbonized Grey, Cyber Orange, Eruption Green, Hot Pepper Red, Lightning Blue, Race Red, Rapid Red, Velocity Blue, Badlands Badge Orange, Azure Gray, Desert Sand, and Solar Orange. Big Foot is also available in White, Pink, Soft Pink, and Purple.
Finish Options
Our protective overlaminate not only increases durability and resistance to UV rays, it also gives us the option of making the vinyl glossy or matte in appearance.
Watch the Install
Dry Install |
Wet Install |
Install Guide
Items you may want to have:
- Detail spray (without wax)
- Microfiber towel or paper towel
- A dish of soapy water (a drop of dish soap in 1-2 cups of water)
- StickerFab Application Fluid (preferred)
- Heat gun or hair dryer
The ideal install temperature (weather) is 75-85F. Do the install in the shade unless it is cooler than 75F. Clean the application area first, and do not use a spray with any type of wax in it.
Wet install is recommended. Use slightly soapy water on the back of the vinyl, which lets you move it around and find the correct alignment. Once aligned, use your fingers to push out the water and air. Use light heat as needed so the overlay does not crease and adheres properly to the OEM emblem.
This Part Fits
| Make | Model | Years |
|---|---|---|
| Ford | Bronco (all trims) | 2021+ |
| Ford | Bronco Sport | 2021+ |
Frequently Asked Questions
|
Does this replace my OEM emblem? No. It goes over your OEM emblem, so you need your factory emblem in place and in good condition. |
Does it fit the Bronco Sport? Yes. It is verified to fit both the Bronco and the Bronco Sport. |
|
How close are the colors to Ford's named colors? As close as printing can get. We matched them using dealership samples and customer-sent swatches, then sampled each in and out of the sun. |
Will it hold up outside? Yes. The overlaminate protects against UV and other elements. |
|
Is it a dry or wet install? We recommend a wet install, and both videos are on this page. |
Can I request a new design? Yes. We are building out the Printed Series, so send us your ideas through our contact form. |
|
What is your return policy? You have 30 days to return it. See our refund policy or email info@stickerfab.com. |
Ford® and Bronco® are registered trademarks of Ford Motor Company. StickerFab is an independent aftermarket manufacturer and is not affiliated with, endorsed by, or sponsored by Ford Motor Company.